Most of the time, the premixed joint compound that comes right out of the bucket is sufficient enough to create a solid Tuscan look (once you mix in the sand). This is probably one of the least messy of all drywall textures basically because it’s applied to the walls and ceiling using a thicker mixed joint compound. Venetians used a mix of limestone, sea salt and silica to create their finish, but today’s modern Tuscan look is easily applied using a mix of joint compound, some fine white sand and a large drywall knife. Tuscan FinishĪlso known as Venetian finish, this stucco-like drywall finish is easy enough to apply because it’s done in such an inconsistent way that it’s nearly impossible to mess up. If you have a bad drywall finish, old popcorn ceiling or a few patches that would make a one eyed pirate jealous – all is well when it’s covered with this drywall texture. Once it’s dry, you can paint it with a heavy nap roller cover.īest of all, this texture is very forgiving. Some drywall finishers like to knock down the texture with a drywall knife, but you can leave it as is for a more pronounced effect. Repeat the process until you’ve got the area covered. Slap a few small circles with the brush until it starts to run low on joint compound and load the brush again. Simply load the stomp brush with your premixed pancake-batter-like-consistency joint compound and slap it against the wall. A painting roller tray filled with a sloppy mix of joint compound and a stomp brush with telescoping handle is all you need to make this texture complete. You don’t need a spray texture hopper gun to apply this drywall texture on walls or ceilings. Mostly used for ceiling textures, a stomp pattern can be rough, slightly textured, symmetrical or completely abstract. A stomp texture is just as its name implies – you stomp it onto the drywall. Not only because it’s so easy to create, but also because it looks so good after it’s done (and probably because it’s all over my house). No: it’s not a bad musical about college hipsters banging on garbage cans with sticks – it’s actually by far my favorite drywall texture. So whether you’re finishing a small room’s walls or your retexturing an entire house, consider these “no mess” drywall textures and you’ll not only minimize the messy white stuff, but you’ll get a favorable drywall texture that everyone is sure to love.

With that said, the following drywall textures aren’t going to be mess-free, but they are certainly going to be the least messy of the bunch. In other words, no matter what you use joint compound for, it’s likely to jump out of the bucket and go everywhere and get on everything you own.

And, just like those overzealous telemarketing jerks who won’t leave you alone, joint compound is sure to start spreading itself around your home like the bird flu.

Eventually, some telemarketer is going to call while you’re in the shower and tick you off something fierce. No mess drywall is kind of like being on the do not call list. Heavier textures may take more time to dry.The title of this article may be a bit deceiving. Allow to dry for 24 hours before painting. How long does it take for ceiling texture to dry?ĭries to the touch in 5-10 minutes and to handle in 10-15 minutes.

Dip the roller into the thinned compound, coating the roller completely.

Prepare a paint roller with an extension pole.

Add some drywall compound to an empty bucket, then add a small amount of water and mix thoroughly to achieve the consistency of a thick but rollable paste.

In respect to this, how do you texture a stomp brush? The best of which come as double headed brushes to speed application. These brushes are referred to as 'crows-foot' brushes. Then stomp the brush on a coated part of the ceiling until the brush achieves a consistent design.Īlso, what does a stomp brush look like? Stomp a random pattern in the mud The preferred style brush to use has stiff bristles aligned in an oval pattern across a wooden base that attaches to an extension pole. Break brush in by applying topping to brush until coated. Similarly one may ask, how do you break in a stomp brush?īreaking in the Brush: The Stipple Brush will change design if not broken in properly before texturing. This turns the texture into a knockdown and makes it look even more professional. Wait for the mud to stiffen after you're finished stomping, and then, if you want to flatten the pattern, scrape the mud lightly with a 10-inch drywall knife.

Stomp ceiling texture